Recent Entries

  • Test the Data of The Crate Mould As A Reference

    All sample inspection records were kept during the test, including various pressures during the processing cycle, melt and Crate Mould(FURNITUREMOULD) temperature, tube temperature, injection time, screw feed cycle, and the like. In short, all future contributions should be retained. Data was succes...
  • The Gating System Is One of The Most Important Issues in The De

    The gating system is one of the most important issues in the design of Daily Necessities Mould(FURNITUREMOULD). The gating system is a complete conveying path that directs the plastic melt from the injection moulding machine nozzle to the mould cavity. It has the functions of mass transfer, pressure...
  • Why Does The Daily Necessities Mould Burst?

    In recent years, China's moulds have developed rapidly, and the technology has also been greatly improved. However, there is still a certain gap at the international level. If we use moulds, there will be some troubles, such as: bursting in the process of using Daily Necessities Mould(FURNITUREMOULD...
  • The Main Steps of The Dustbin Mould Test(2)

    Develop a standard Dustbin Mould(FURNITUREMOULD) test program that can be used to establish daily work methods. 1. Make reasonable adjustments to reduce the total processing cycle. 2. Operate the new transfer conditions for at least 30 minutes to stabilize, then continuously produce at least a doz...
  • The Main Steps of The Dustbin Mould Test (1)

    In order to avoid unnecessary waste of time and mass production, it is necessary to patiently adjust and control various processing conditions, find the best temperature and pressure conditions, and develop a standard Dustbin Mould(FURNITUREMOULD) test program that can be used to establish daily wor...
  • The Plastic Flow in The Dustbin Mould Is A Fountain Flow

    In injection moulding, do you often have problems with floating fibers, fibers are fiberglass on the surface of the product, rough, and the appearance is more difficult to accept. In injections, although the flow of material differs from the flow of liquid (liquid is Newtonian flow, plastic is non-N...
  • Design Basis for Daily Necessities Mould

    1. Dimensional accuracy and its relative size According to the specific requirements and functions of the overall products of plastic products, it is necessary to determine the appearance quality and specific dimensions of Daily Necessities Mould(FURNITUREMOULD): plastic products with higher appear...
  • Very Low Temperatures in The Dustbin Mould Can Cause Surface De

    Even when the melt enters the Dustbin Mould(FURNITUREMOULD), the injection speed is constant and its flow rate changes. When entering the mould gate area, the melt flow rate is high, but after entering the mould cavity, that is, the waste box mould-filling stage, the melt flow rate begins to decreas...
  • The Design of The Dustbin Mould Determines The Warpage Tendency

    Fundamentally, the design of the Dustbin Mould(FURNITUREMOULD) determines the warpage tendency of the part. It is difficult to suppress this trend by changing the moulding conditions. Finally, the problem must be solved through mould design and improvement. This phenomenon is mainly caused by the fo...
  • Strictly Control The Temperature of Each Heated Part of The Dus

    In production, it is often encountered that a heating coil is damaged or the heating control portion is out of control, and the temperature of the Dustbin Mould(FURNITUREMOULD) is drastically changed to cause chromatic aberration. The chromatic aberration caused by these causes is easy to determine....
  • Working Condition of The Dustbin Mould

    When using the Dustbin Mould(FURNITUREMOULD), the working conditions of the mould are very wide, and the working conditions of the various moulds are very different. Therefore, the materials used to make the dustbin mould have a wide range, and the application of the mould material in the mould mate...
  • What Is A Good Dustbin Mould (าป)

    There are questions when you are looking for a manufacturer for dustbin mould. We must see that injection moulds are the basic tool for manufacturing quality products, so we provide tips on the quality of the Dustbin Mould(FURNITUREMOULD) as our manufacturing experience. 1. Product design Why list...
  • Large Mould Processing for The Dustbin Mould

    For large moulds such as Dustbin Mould(FURNITUREMOULD), there is usually no steel plate of the required size from a toll or forged billet. Even with steel sheets of these sizes, it is less economical to directly process the cavity into such a large metal sheet. An important factor is that cast stee...
  • Dustbin Mould Maintenance Process

    1. All water pipes should be drained and all residual water should be dried to avoid rust due to accumulated water. There must be no water trapped in the Dustbin Mould(FURNITUREMOULD). 2. Check to make sure all bolts, plates, clamps, etc. are in place. 3. Take the last shot as an example of the ty...
  • Preventive Maintenance Program for Household Product Mould

    You can make a cheap Household Product Mould(FURNITUREMOULD) that has problems but won't last long, or you can build a well-known factor that provides long life and minimal mould maintenance for household products. Household product mould that become unusable due to wear, abuse, and improper structu...
  • Solutions to Damage on The Surface or Inside of Household Produ

    In order to reduce or eliminate the erosion of corrosive plastics on the surface of Household Product Mould(FURNITUREMOULD), their decomposition products, electroplating may be most helpful. The electroplater must know exactly what the attack media is suggesting appropriate e. Gold has been used for...
  • Possible Problems With Household Product Mould After Prolonged

    Household Product Mould(FURNITUREMOULD) fasteners are loose for a variety of reasons: clamping force causes home product mould compression, impact and burst pressure caused by rapid mould filling, tensile stress when the household product mould is pulled apart - all these forces are Enhanced during ...
  • Alternatives to No Flow Table Mould from Multiple Systems

    In view of the high cost of a no-flow Table Mould(FURNITUREMOULD), it is desirable to consider alternatives provided by multiple systems, through various regions and entry locations of the manifold, and the type of tip. The design chosen must facilitate the use of the basic runner and gate system co...
  • Warping Problem of Furniture Mould

    The warp formed after removal from the Furniture Mould(FURNITUREMOULD) is very common and is always the result of freezing stress, differential shrinkage, or filler material, filler orientation. This is almost always a processing problem, but it can also be caused by a mechanical failure or incorrec...
  • Improvements in Furniture Mould And Materials With More Free Fl

    Improvements in Furniture Mould(FURNITUREMOULD) and the use of more free-flowing grades are ways to reduce the impact of weld lines, but the main factor involved is finding the best processing conditions. With regard to furniture mould, it is rarely advantageous to feed from two or more doors. This...
  • How to Deal With The Warpage of Furniture Mould

    When warpage occurs, the injection rate should be checked first. The short molded article should then be produced by the method described in the short molded portion to determine how the Furniture Mould(FURNITUREMOULD) is filled. Furthermore, it is determined that the filler is uniform and that the ...
  • How to Improve The Quality of Furniture Mould Manufacturing

    Although Furniture Mould(FURNITUREMOULD) design is carried out under the expected process conditions when selecting molding materials and molding equipment, people's understanding is often imperfect. Therefore, after the furniture mould is processed, a mold test must be performed to observe the mold...
  • Table Mould Heat Treatment Problem

    Table Mould(FURNITUREMOULD) heat treatment is an important means to improve the hardness of steel. Usually, after the mold is opened, heat treatment is carried out and then refined, but the process is also risky. If improper treatment will cause cracks in steel and scrap, what is the cause of the ab...
  • Steel Is The Decisive Factor In The Quality of Furniture Mould

    Steel is the decisive factor in the quality of Furniture Mould(FURNITUREMOULD). Choosing the right steel is the top priority. The criteria for choosing steel are: 1. Requirements for injection molding materials - Different plastics should use different steel materials, such as high polishing and co...
  • Demand for Household Product Mould Continues to Expand

    With the development of China's industrial manufacturing industry, after decades of mold manufacturing technology accumulation, mold products have been gradually applied to all walks of life, showing a trend of vertical and horizontal depth. Under the background of the advancement of Household Produ...